Response Code |
Description |
Remarks |
|---|---|---|
-1 |
"FAILED" |
Failed to process request. |
0 |
"OK" |
Request processed successfully. |
1 |
"Common error" |
Common error. |
2 |
"Configuration syntax error" |
Configuration syntax error. |
3 |
"Unsupported request" |
Unsupported request. |
4 |
"Incorrect parameter" |
Parameters such as channelID are incorrectly set. |
5 |
"Incorrect device ID" |
Incorrect device ID. |
6 |
"Incorrect channel ID" |
Incorrect channel ID. |
7 |
"Incorrect serial port number" |
Incorrect serial port number. |
8 |
"Incorrect alarm port number" |
Incorrect alarm port number. |
9 |
"Unsupported media type" |
Unsupported media type. |
10 |
"Failed to modify server config" |
Failed to modify server configurations. |
11 |
"Only some parameters configured successfully" |
Only some parameters are set successfully. |
12 |
"The number of plans exceeded the maximum value" |
The number of plans exceeded the maximum. |
13 |
"No hard disk on the device" |
The device does not have a hard disk. |
14 |
"Failed to enable the audio device" |
Failed to enable the audio device. |
15 |
"The server's voice intercom is in use" |
The server's voice intercom is in use. |
16 |
"The device is busy" |
The device is busy. |
17 |
"Internal error" |
Internal error. |
18 |
"Failed to allocate resource" |
Resource allocation error. |
19 |
"Flash error" |
Flash error. |
20 |
"Unsupported video standard" |
Unsupported video standard. |
21 |
"Unsupported alarm linkage action" |
Unsupported alarm linkage action. |
22 |
"IP address conflict" |
IP addresses conflict with each other. |
23 |
"LTE or DHCP conflict" |
LTE settings conflict with DHCP settings. |
24 |
"SIP stack error" |
SIP protocol stack error. |
32 |
"Password weak format" |
The password complexity does not meet the requirements. |
33 |
"Please increase the space percentage." |
Increase the space percentage. |
35 |
"Incorrect configuration file password" |
Incorrect configuration file password. |
36 |
"Failed to enable the service, please check whether the corresponding algorithm has been installed" |
Failed to enable the service. Check whether the required algorithm has been installed. |
37 |
"Itgt service not init" |
Initializing ITGT is incomplete. |
45 |
"The multicast and unicast switches must be disabled." |
Both multicast and unicast functions need to be disabled. |
46 |
"Multicast or unicast switch. At least one switch must be enabled." |
Either the multicast or unicast function needs to be enabled. |
60 |
"Time period overlap" |
Time segments in the time plan overlap. |
61 |
"Incorrect IP address" |
Incorrect IP address. |
62 |
"Failed to connect to the server" |
Server connection failure. |
70 |
"No records found" |
No record is found. |
100 |
"Null pointer" |
The pointer is null. |
101 |
"Null element" |
The XML file does not have the corresponding node. |
102 |
"Failed to verify the user name or password" |
Incorrect user name or password. |
103 |
"Failed to verify the version file" |
Failed to verify the version file. |
104 |
"Failed to verify the kernel upgrade file" |
Failed to verify the kernel upgrade file. |
105 |
"Failed to verify the system upgrade file" |
Failed to verify the file system upgrade file. |
106 |
"First login" |
Initial login succeeded. |
107 |
"The client has logged in to the device" |
A client has logged in. |
108 |
"The user is locked" |
The user is locked. |
109 |
"The number of users exceeded the maximum value" |
The number of users exceeded the maximum. |
110 |
"User name conflict" |
Duplicate user name. |
111 |
"No user name" |
The user does not exist. |
112 |
"User no power" |
The user does not have the permission. |
113 |
"No need to upgrade the version. The current version is the same as the upgrade version" |
No upgrade is required because the versions are consistent. |
114 |
"Unsupported capability parameter" |
The capability parameter is not supported. |
115 |
"The preset has been configured as the home position" |
The preset position has been configured as the home position. |
116 |
"The preset has been added to the tour track" |
The preset position has been added to the tour. |
117 |
"Failed to set eth type" |
Failed to set the network port type. |
118 |
"Failed to set eth mode" |
Failed to set the network port rate. |
119 |
"Upload config type error" |
The type of the configuration file to upload is incorrect. |
120 |
"DNS server unreachable" |
The DNS server is unreachable. |
121 |
"DNS server no domain" |
The DNS server failed to obtain the domain name. |
122 |
"The tour track is being executed" |
The tour is being executed. |
123 |
"DHCP get option failed" |
DHCP failed to obtain a message. |
124 |
"The SD card is formatting" |
The SD card is being formatted. |
125 |
"The device is upgrading" |
The system is being upgraded. |
126 |
"The device is rebooting" |
The system is being restarted. |
127 |
"Restoring to the default settings" |
The device is restoring default settings. |
128 |
"No configuration operation is allowed during restoration" |
Configuration operations cannot be performed during default setting restoration. |
129 |
"Failed to set the ROI in the Motion Joint Photographic Experts Group (MJPEG) standard" |
Failed to set the ROI in the MJPEG standard. |
130 |
"Failed to set the ROI for the secondary stream when only the primary stream is available" |
The ROI failed to be set for the secondary stream when only the primary stream is available. |
131 |
"A conflict occurred when enabling tripwire detection" |
A conflict occurred when tripwire crossing detection is enabled. |
132 |
"A conflict occurred when enabling object counting" |
A conflict occurred when object counting is enabled. |
133 |
"A conflict occurred when enabling motion detection" |
A conflict occurred when motion detection is enabled. |
134 |
"A conflict occurred when enabling tripwire detection" |
A conflict occurred when tripwire crossing detection is enabled. |
135 |
"A conflict occurred when enabling area detection" |
A conflict occurred when intrusion detection, abandoned object detection, or removed object detection is enabled. |
136 |
"A conflict occurred when enabling video interference" |
A conflict occurred when video interference detection is enabled. |
137 |
"A conflict occurred when enabling illuminance enhancement or lens block if the intelligent switch is enabled" |
Failed to enable lens blocking detection or illuminance enhancement because the behavior analysis function is enabled. |
138 |
"A conflict occurred when enabling the intelligent switch or lens block if illuminance enhancement is enabled" |
Failed to enable behavior analysis or lens blocking detection because the illuminance enhancement function is enabled. |
139 |
"A conflict occurred when enabling the intelligent switch or illuminance enhancement if lens block is enabled" |
Failed to enable behavior analysis or illuminance enhancement because the lens blocking detection function is enabled. |
140 |
"Failed to set intelligent services when the intelligent switch is not enabled" |
Failed to set the intelligent service because the intelligent analysis function is not enabled. |
141 |
"The number of tripwires exceeded the maximum value" |
The number of tripwires exceeded the maximum. |
142 |
"The number of areas of the same type exceeded the maximum value 4" |
The number of configured areas exceeded the maximum (4). |
143 |
"The number of areas exceeded the maximum value 10" |
The number of configured areas exceeded the maximum (10). |
144 |
"You must set at least one area" |
You must set at least one area. |
145 |
"The number of angles of the area exceeded the maximum value" |
The number of area vertexes exceeded the maximum. |
146 |
"A conflict occurred when setting removed object detection if abandoned object detection is enabled" |
A conflict occurred when abandoned object detection is enabled. The removed object detection has been enabled. |
147 |
"A conflict occurred when setting abandoned object detection if removed object detection is enabled" |
A conflict occurred when removed object detection is enabled. The removed object detection has been enabled. |
148 |
"Failed to set global parameters for the intelligent analysis algorithm" |
Failed to set global parameters for the intelligent analysis algorithm. |
149 |
"Failed to set an intelligent analysis area" |
Invalid intelligent analysis area. |
150 |
"The size of the privacy mask area exceeded that of the total area" |
The privacy mask area exceeded the total area. |
151 |
"Conflict between the bandwidth autonegotiation and encoding type or bit rate type" |
The adaptive bandwidth function conflicts with the encoding type or bit rate type. |
152 |
"The IP filtering rule already exists" |
Duplicate IP address filtering rule. |
153 |
"A conflict occurred when setting the frame format 50 or 60 frame if WDR is auto or manual mode" |
If the WDR mode is set to manual or auto, the collection frame rate cannot be set to 50 or 60 fps. |
154 |
"A conflict occurred when setting the WDR mode auto or manual if frame format 50 or 60 frame" |
If the collection frame rate is set to 50 or 60 fps, the WDR mode cannot be set to manual or auto. |
155 |
"A conflict occurred when enabling illuminance enhancement if the intelligent or lens block switch is enabled" |
Failed to set the illuminance enhancement because the lens blocking detection or behavior analysis function is enabled. |
156 |
"Failed to set tour track parameters during a tour" |
Failed to set tour parameters during a tour. |
157 |
"The device is not enabled" |
The device is not started. |
158 |
"Failed to delete a preset in use" |
Failed to delete the preset position in use. |
159 |
"Nonexistent intelligent analysis area" |
The intelligent analysis area does not exist. |
160 |
"Nonexistent intelligent analysis line" |
The intelligent analysis line does not exist. |
161 |
"Nonexistent privacy mask area" |
The privacy mask area does not exist. |
162 |
"In user define scan" |
Pattern scan is in progress (many functions are unavailable). |
163 |
"Set DRC backlight conflict" |
The backlight compensation and DRC functions cannot be enabled at the same time. |
164 |
"Cruise in guard position" |
A preset position in the tour has been configured as the home position. |
165 |
"The SD card is abnormal" |
SD card exception. |
166 |
"Privacy protection area overlap" |
Privacy mask areas overlapped. |
167 |
"Modify Pwd to be the same as the original Pwd" |
The new password must be different from the old password. |
168 |
"Upgrade file version is too low, please select a high version upgrade" |
The version of the upgrade file is too early. Select an upgrade file of a later version. |
169 |
"Too many video files" |
Too many recording files. |
170 |
"Operation conflict with mosaic" |
The operation conflicts with the mosaic setting. |
171 |
"Operation conflicts with OSD" |
The operation conflicts with the OSD setting. |
172 |
"Operation conflicts with image overlay" |
The operation conflicts with image overlay. |
173 |
"Video encoder is not turned on" |
The video encoder is not started. |
175 |
"The lower limit of the color temperature in the white balance automatic tracking mode is greater than or equal to the upper limit of the color temperature" |
The lower limit of the color temperature must be less than the upper limit in automatic tracking white balance mode. |
176 |
"MJPEG does not support digital watermarking" |
The MJPEG does not support the digital watermark function. |
178 |
"Current full frame rate and wide dynamic are mutually exclusive" |
The 50 or 60 fps conflicts with WDR or BLC. |
179 |
"OSD character length error" |
The OSD character length is incorrect. |
183 |
The SD card is not mounted |
The SD card is not mounted. |
184 |
"Importing target database, later" |
Importing target images into a target library... |
185 |
"Adding targets, later" |
Importing a single target image into a target library... |
186 |
"The common intelligent analysis alarm with the ITS alarm conflicts. They cannot be enabled at the same time." |
The common intelligent analysis alarm conflicts with the ITS alarm. They cannot be enabled at the same time. |
187 |
"The ITS alarm conflicts with the common intelligent analysis alarm. They cannot be enabled at the same time." |
The ITS alarm conflicts with the common intelligent analysis alarm. They cannot be enabled at the same time. |
190 |
"External device open fail" |
Failed to enable the ITS device. |
194 |
"The number of encrypted channels exceeds the limit" |
The number of encrypted channels reaches the upper limit. |
197 |
"GB35114 First Login Requires PIN Code Modification" |
The PIN needs to be changed upon the first login in GB 35114 software mode. |
198 |
"Request encrypted stream failed" |
Failed to request encrypted media streams (due to insufficient resources). |
200 |
"Audio anomaly detection is not supported when the audio input is in mic in mode" |
The audio existence detection is not supported when the audio input is in mic in mode. |
202 |
"The CIF resolution and corridor mode are mutually exclusive" |
The CIF resolution and corridor mode cannot be enabled at the same time. |
211 |
"The point is out of range" |
The point is out of range. |
212 |
"The line become a point" |
The start point overlaps with the end point. |
213 |
"The lines cross" |
Intersecting lines. |
214 |
"Manual exposure and wide dynamic are mutually exclusive" |
Manual exposure and WDR cannot be enabled at the same time. |
215 |
"Manual exposure and background frequency are mutually exclusive" |
The manual exposure and background frequency cannot be enabled at the same time. |
216 |
"Manual exposure and glare suppression are mutually exclusive" |
Manual exposure and highlight compensation cannot be enabled at the same time. |
217 |
"Exposure mode shutter priority and wide dynamic are mutually exclusive" |
The shutter priority exposure mode and WDR cannot be enabled at the same time. |
218 |
"Exposure mode shutter priority and background frequency are mutually exclusive" |
The shutter priority exposure mode and background frequency cannot be enabled at the same time. |
219 |
"Exposure mode shutter priority and glare suppression are mutually exclusive" |
The shutter priority exposure mode and highlight compensation cannot be enabled at the same time. |
220 |
"Backlight compensation and wide dynamic are mutually exclusive" |
Backlight compensation and WDR cannot be enabled at the same time. |
221 |
"Backlight compensation and glare suppression are mutually exclusive" |
Backlight compensation and highlight compensation cannot be enabled at the same time. |
222 |
"Wide dynamic and glare suppression are mutually exclusive" |
WDR and highlight compensation cannot be enabled at the same time. |
223 |
"Through fog mode and wide dynamic are mutually exclusive" |
The defogging mode and WDR cannot be enabled at the same time. |
224 |
"Glare suppression and 50 frames and 60 frames are mutually exclusive" |
Highlight compensation is mutually exclusive with the frame rate of 50 or 60 fps. |
225 |
"Wide dynamic and 50 frames and 60 frames are mutually exclusive" |
WDR is mutually exclusive with the frame rate of 50 or 60 fps. |
226 |
"Manual exposure and backlight compensation are mutually exclusive" |
Manual exposure and backlight compensation cannot be enabled at the same time. |
227 |
"Glare suppression and slow shutter are mutually exclusive" |
Highlight compensation and slow shutter cannot be enabled at the same time. |
228 |
"Wide dynamic and slow shutter are mutually exclusive" |
WDR and slow shutter cannot be enabled at the same time. |
231 |
"Dehaze and fog detect are mutually exclusive" |
Defogging and fog detection cannot be enabled at the same time. |
232 |
"Fog detect and dehaze are mutually exclusive" |
Fog detection and defogging cannot be enabled at the same time. |
233 |
"Backadapt and slow shutter are mutually exclusive" |
Backlight adaptation and slow shutter cannot be enabled at the same time. |
234 |
"Manual exposure and Backadapt are mutually exclusive" |
Manual exposure and backlight adaptation cannot be enabled at the same time. |
235 |
"BackLight and Backadapt are mutually exclusive" |
Backlight compensation and backlight adaptation cannot be enabled at the same time. |
236 |
"NearLight and FarLight are mutually exclusive" |
Low beam and high beam cannot be enabled at the same time. |
237 |
"RS485 and extlight are mutually exclusive" |
The RS-485 external illuminator and transparent channel or PTZ channel cannot be enabled at the same time. |
238 |
"Mixmode and slow shutter are mutually exclusive" |
The full intelligence mode and slow shutter cannot be enabled at the same time. |
239 |
"Setting failed. Disable image combination first." |
Snapshot resolution and image combination cannot be enabled at the same time. |
240 |
"SuperCoding initialization failed. Please try again." |
Failed to initialize SuperCoding. Please try again. |
241 |
"Please turn off SuperCoding first." |
Disable SuperCoding first. |
242 |
"Corridor mode, SuperCoding, and perimeter detection cannot be enabled at the same time." |
The corridor mode, SuperCoding, and intelligent perimeter detection cannot be enabled at the same time. |
246 |
"SuperCoding and corridor mode cannot be enabled at the same time." |
SuperCoding and corridor mode cannot be enabled at the same time. |
247 |
SuperCoding cannot be enabled for both primary and secondary streams simultaneously. Disable SuperCoding for the primary or secondary stream first. |
SuperCoding cannot be enabled for the primary and secondary streams at the same time. Disable SuperCoding for the primary or secondary stream first. |
248 |
"Super encoding is not supported when the frame rate is greater than 30." |
SuperCoding is not supported when the frame rate is greater than 30 fps. |
249 |
Backlight adaptation and Glare suppression are mutually exclusive |
Backlight adaptation and highlight compensation cannot be enabled at the same time. |
250 |
Backlight adaptation and 50 frames and 60 frames are mutually exclusive |
Backlight adaptation and frame rate 50 fps or 60 fps cannot be enabled at the same time. |
251 |
"Camera-Supercoding license invalid" |
The SuperCoding license is invalid. |
252 |
"Electronic image stabilization is mutually exclusive with full intelligence mode." |
Image stabilization and full intelligence cannot be enabled at the same time. |
253 |
"Full frame rate(50Hz/60Hz) is mutually exclusive with target intelligence, vehicle intelligence, behavior analysis and situation analysis." |
The full frame rate (50 Hz/60 Hz) is mutually exclusive with target detection, object classification, behavior analysis, and situation analysis. |
254 |
"target intelligence, vehicle intelligence, behavior analysis and situation analysis is mutually exclusive with Full frame rate(50Hz/60Hz)." |
Target detection, object classification, behavior analysis, and situation analysis are mutually exclusive with the full frame rate (50 Hz/60 Hz). |
256 |
"No files are available for sending." |
No file can be sent. |
260 |
"extlight and RS485 are mutually exclusive" |
The transparent channel or PTZ channel is mutually exclusive with the RS-485 external illuminator. |
300 |
"File download failed" |
File download failed. |
301 |
"Connection server interrupt" |
Disconnected from the server. |
302 |
"Request timed out" |
Request timeout. |
303 |
"Connection failure" |
Server connection failure. |
304 |
"Connection not found" |
The connection is not found. |
305 |
"Reconnecting server" |
Reconnecting to the server... |
306 |
"File does not exist" |
The file does not exist. |
307 |
"No permission to upload file" |
Failed to verify the file upload permission. |
310 |
"Illegal upgrade file" |
File error. |
311 |
"Damaged file" |
The file is corrupted. |
312 |
"Incorrect file format" |
The file format is incorrect. |
350 |
"Upgrade type invalid" |
The upgrade file type does not match the request type. |
351 |
"Upgrade param null" |
The upgrade parameter is empty. |
352 |
"Upgrade file unload" |
The upgrade file is not uploaded. |
353 |
"Upgrade file verify fail" |
Failed to verify the integrity of the upgrade file. |
354 |
"Upgrade sign fail" |
Failed to verify the digital signature of the upgrade file. |
355 |
"Upgrade space full" |
The upgrade storage space is full. |
356 |
"Upgrade support device list fail" |
Failed to adapt the device list. |
357 |
"The algorithm package version is incorrect (the algorithm needs to be the same as the package VRC version)" |
The algorithm package version is incorrect. The algorithm package version must be consistent with the VRC version of the software package. |
358 |
"After the version package upgraded, need to upgrade algorithm package" |
The algorithm package needs to be upgraded after the version package is upgraded. |
359 |
"OMNI rotatable device upgrade failed" |
Failed to upgrade the rotatable lens of the omni-data structuring camera. |
360 |
"Failed to cancel the upgrade, when the device is updating files, the user is not allowed to cancel the upgrade" |
Failed to cancel the upgrade. You are not allowed to cancel the upgrade when the device is updating files. |
361 |
"need upgrade target algorithm package" |
The target-related algorithm package needs to be upgraded. |
362 |
"need upgrade Motor vehicle/Non-motor vehicle/Pedestrian algorithm package" |
The object classification algorithm package needs to be upgraded. |
363 |
"OMNI rotatable device 2001 upgrade failed" |
Failed to upgrade the rotatable lens 2001 of the omni-data structuring camera. This code is returned when one of the two rotatable lenses fails to be upgraded. |
364 |
"OMNI rotatable device 2002 upgrade failed" |
Failed to upgrade the rotatable lens 2002 of the omni-data structuring camera. This code is returned when one of the two rotatable lenses fails to be upgraded. |
365 |
"Rollback is not allowed on singleton system version" |
Version rollback is not supported after device power-off in dual-system mode. |
366 |
"Device is rebooting" |
The device is being restarted. |
367 |
"Device model is not in white list" |
Failed to verify the trustlist. |
390 |
"Period not set" |
Failed to set the period, causing the failure of setting automatic restart parameters. |
391 |
"Start time out of range" |
The start time of the automatic restart plan is not within the proper range. |
601 |
"SD card is not formatted" |
The SD card is not formatted. |
602 |
"Custom package is undefined" |
The stream profile and ISP profile are not defined. |
603 |
"PTZ has not stopped" |
Failed to disable pattern scan because the PTZ is not stopped. |
605 |
"Code stream type and intelligent target detection function are mutually exclusive" |
The stream type and the intelligent target detection function cannot be enabled at the same time. |
606 |
"Sub-stream resolution and intelligent target detection are mutually exclusive" |
The secondary stream resolution and the intelligent target detection function cannot be enabled at the same time. |
607 |
"The number of panoramic privacy records exceeds the maximum" |
The number of panoramic privacy masks exceeds the upper limit. |
650 |
"Incorrect port" |
Incorrect port settings. |
651 |
"Incorrect username or password" |
Incorrect user name or password settings. |
652 |
"Incorrect IP address" |
Incorrect IP address settings. |
700 |
"The area does not exist and the index value is incorrect" |
The area to be deleted, moved, or modified does not exist. The index is invalid. |
701 |
"The horizontal width of the area exceeds 180 degrees" |
The horizontal width of the area to be added or modified exceeded 180 degrees. |
702 |
"The area coordinate point does not match the lower left and upper right rules" |
The vertical direction of the area to be added or modified does not comply with the lower-left and upper-right rules. |
705 |
"The new zone index number is illegal and the index already exists" |
The index number of the new area is invalid. The index already exists. |
708 |
"The horizontal or vertical coordinates of the area coordinate points are equal" |
The horizontal coordinate and vertical coordinate of the area are the same. |
709 |
"The area index number is illegal, less than 1" |
The index number of the area must be greater than or equal to 1. |
710 |
"Duplicate area index number" |
Duplicate index number of the area. |
800 |
"Daylight saving time is already open" |
The DST has been enabled. |
900 |
"Anti-shake and regional cropping are mutually exclusive" |
Electronic image stabilization and area cropping cannot be enabled at the same time. |
901 |
"Regional cropping and anti-shake are mutually exclusive" |
Area cropping and electronic image stabilization cannot be enabled at the same time. |
902 |
"Electronic anti-shake service and license plate detection are mutually exclusive" |
Electronic image stabilization and license plate detection cannot be enabled at the same time. |
903 |
"GPS time synchronization is enabled. Please disable it first." |
GPS time synchronization has been enabled. Disable it first. |
950 |
"Pointer is NULL" |
The pointer is null. |
951 |
"Failed to read file" |
Failed to read the file. |
952 |
"Failed to parse XML" |
Failed to parse the XML file. |
953 |
"Image type is not support" |
The image format is not supported. |
954 |
"Resolution is different from initial" |
The resolution is different from the initial resolution. |
955 |
"Vertex is illegal" |
Improper coordinates. |
956 |
"Resolution is unsupport" |
Unsupported resolution. |
957 |
"Plate Parameter error" |
Incorrect parameter for license plate detection. |
958 |
"Malloc failed" |
Memory allocation failed. |
961 |
"Config error" |
Configuration error. |
962 |
"Detect Parameter set error" |
The detection parameter is set incorrectly. |
963 |
"Lane Line error" |
Incorrect lane line. |
965 |
"Setting failed as detection line is out of the range of lane lines" |
The traffic flow detection line is out of range. |
968 |
"Setting failed. Lower the snapshot resolution first." |
Image combination and 8-megapixel resolution cannot be enabled at the same time. |
980 |
"Plate recognition is not enabled" |
License plate recognition is not enabled. |
981 |
"The OSD position of the composite image is mutually exclusive with the original image and close-up image." |
The OSD text of the combined image overlaps with that of the original image and close-up image respectively. |
982 |
"The OSD position of the original image is mutually exclusive with that of the composite image." |
The OSD text of the combined image overlaps with that of the original image. |
983 |
"The OSD position of the close-up image is mutually exclusive with that of the composite image." |
The OSD text of the combined image overlaps with that of the close-up image. |
1001 |
"The Certificate key is too short" |
The license RSA public key is too short. |
1002 |
"The Certificate key is too weak" |
The license signature algorithm is too weak. |
1004 |
"Certificate Private key password not match" |
The private key of the certificate does not match the password. |
1024 |
"VM ret fail" |
Failed to invoke the VM interface. |
1100 |
"Lane line type is out of range" |
Invalid lane line type. |
1101 |
"The number of lanes is not within the valid range" |
Invalid lane quantity. |
1102 |
"Lane direction is invalid" |
Invalid lane direction. |
1103 |
"Lane driving direction is invalid" |
Invalid driving direction. |
1104 |
"Lane use is invalid" |
Invalid lane. |
1105 |
"Lane attribute is invalid" |
Invalid lane attribute. |
1106 |
"Driving direction is invalid" |
Invalid driving direction. |
1107 |
"Direction is invalid" |
Invalid direction. |
1108 |
"Car logo speed is invalid" |
Invalid marked speed for small vehicles. |
1109 |
"Car limit low speed is invalid" |
Invalid lower speed limit for small vehicles. |
1110 |
"Car limit high speed is invalid" |
Invalid upper speed limit for small vehicles. |
1111 |
"Big car logo speed is invalid" |
Invalid marked speed for large vehicles. |
1112 |
"Big car limit low speed is invalid" |
Invalid lower speed limit for large vehicles. |
1113 |
"Big car limit high speed is invalid" |
Invalid upper speed limit for large vehicles. |
1114 |
"External light association is invalid" |
Invalid external light source. |
1115 |
"The capture interval is not within the valid range" |
Invalid snapshot interval. |
1116 |
"Detection method is not within the valid range" |
Invalid detection method. |
1117 |
"The number of violations exceeds the limit" |
The number of violations exceeded the maximum. |
1118 |
"Violation type is invalid" |
Invalid violation type. |
1119 |
"The number of violations captured is not within the valid range" |
The number of traffic violation snapshots is out of range. |
1120 |
"Red light priority is invalid" |
Invalid red light access mode. |
1121 |
"Pressure lane line sensitivity is invalid" |
Invalid sensitivity for detecting marked lanes violations. |
1122 |
"Machine accounted for non-residence time is invalid" |
Invalid dwell duration for non-motorized vehicles moves or stays on a motor vehicle line. |
1123 |
"Bus lane time is invalid" |
Invalid value for a non-bus motor vehicle moves or stays on a bus lane. |
1124 |
"Yellow grid line dwell time is invalid" |
Invalid dwell duration for detecting parking in yellow zones. |
1125 |
"Signal access mode is not within the valid range" |
The traffic light access mode is out of range. |
1126 |
"Number of semaphore areas is invalid" |
Invalid number of traffic light areas. |
1127 |
"Number of lights is invalid" |
Invalid number of traffic lights. |
1128 |
"Signal direction is invalid" |
Invalid signal direction. |
1129 |
"Yellow light duration is invalid" |
Invalid yellow light duration. |
1130 |
"The semaphore area is invalid" |
Invalid signal area. |
1131 |
"The detection line and stop line are not within the effective range of the lane line or the right boundary line" |
The detection line or stop line is out of the lane line or right boundary range. |
1132 |
"If the car limits the low speed to be greater than the limit speed, return error" |
The vehicle lower speed limit is higher than the upper speed limit. |
1133 |
"The car logo speed is not at low speed, return error" |
The vehicle marked speed is lower than the lower speed limit. |
1134 |
"If the cart is slower than the high speed, return error" |
The marked speed for large vehicles is out of range. |
1135 |
"If the speed of the cart is not at a low speed, return error" |
The marked speed for large vehicles is lower than the lower speed limit. |
1136 |
"ITS return data is invalid" |
Invalid ITS return value. |
1137 |
"ITS congestion threshold is invalid" |
Invalid ITS congestion threshold. |
1138 |
"ITS snap interval type is invalid" |
Invalid ITS snapshot interval type. |
1139 |
"ITS adaptive snap low speed is invalid" |
Invalid ITS automatic snapshot speed. |
1140 |
"ITS adaptive snap mid speed is invalid" |
Invalid ITS automatic snapshot speed. |
1141 |
"ITS adaptive snap low speed interval is invalid" |
Invalid ITS automatic snapshot interval. |
1142 |
"ITS adaptive snap mid speed interval is invalid" |
Invalid ITS automatic snapshot interval. |
1143 |
"ITS adaptive snap high speed interval is invalid" |
Invalid ITS automatic snapshot interval. |
1144 |
"The setting fails. The lane line and the right lane of the lane are drawn from left to right" |
The lane lines are drawn incorrectly. |
1146 |
"Signal light repeat" |
Duplicate traffic light. |
1147 |
"The front line should be drawn below the stop line" |
The front detection line should be drawn below the stop line. |
1148 |
"Please turn off corridor mode first." |
Disable the corridor mode first. |
1174 |
"The snapshot mode is not supported" |
The capture mode (single-shutter or dual-shutter) is not supported in the current ITS application mode. |
1175 |
"The pedestrian running red light or entrance/exit mode is enabled, the corridor mode cannot be enabled." |
The corridor mode cannot be enabled when the entrance and exit mode and pedestrian running-red-light detection mode is enabled. |
1176 |
"NMV captures offset position, the second one is earlier than the first one" |
The position that triggers the second snapshot of non-motorized vehicles must be above that of the first snapshot. |
1177 |
"NMV captures offset position, the third one is earlier than the second one" |
The position that triggers the third snapshot of non-motorized vehicles must be above that of the second snapshot. |
1178 |
"The pre recording time parameter for video recording is illegal" |
Invalid pre-recording time. |
1179 |
"The timeout parameter for recording is illegal" |
Invalid recording timeout interval. |
1180 |
"The snap type is switched successfully. please" |
The snapshot mode (strobe or flash mode) is switched at ITS checkpoints or entrances/exits. |
1251 |
"The selected time range cannot be less than 2 minutes" |
The reversible lane policy must take effect for at least 2 minutes. |
1252 |
"The self-developed overseas ITS detection algorithm license is illegal." |
Invalid license of the in-house basic detection algorithm for ITS cameras outside the Chinese mainland. |
1253 |
"The self-developed overseas machines occupy non-algorithmic licenses illegally." |
Invalid license of the in-house algorithm for detecting motor vehicles in non-motorized vehicle lanes outside the Chinese mainland. |
1254 |
"Developing overseas occupancy emergency lane algorithm License is illegal." |
Invalid license of the in-house algorithm for detecting emergency lane violations outside the Chinese mainland. |
1255 |
"The self-developed overseas impolite pedestrian algorithm license is illegal." |
Invalid license of the in-house algorithm for detecting vehicles failing to yield to pedestrians outside the Chinese mainland. |
1256 |
"The self-developed overseas yellow web grid non-compliant algorithm license is illegal." |
Invalid license of the in-house algorithm for detecting yellow zone parking violations outside the Chinese mainland. |
1257 |
"The license for our self-developed overseas occupation of bus lanes algorithm is illegal." |
Invalid license of the in-house algorithm for detecting bus lane violations outside the Chinese mainland. |
1258 |
"Self-developed overseas non-licensing safety belt algorithm license is illegal." |
Invalid license of the in-house algorithm for detecting seat belt violations outside the Chinese mainland. |
1259 |
"The self-developed overseas driving call algorithm License is illegal." |
Invalid license of the in-house algorithm for detecting hands-free device violations outside the Chinese mainland. |
2000 |
"Please turn off the license plate recognition function first" |
Disable the license plate recognition function. |
2001 |
"Please turn off target detection first" |
Disable target detection. |
2002 |
"Please turn off the parking detection function first" |
Disable parking detection. |
2003 |
"Please turn off behavior analysis first" |
Disable behavior analysis. |
2004 |
"Please turn off the line statistics function first" |
Disable head counting. |
2005 |
"Please turn off automatic tracking first" |
Disable automatic tracking. |
2006 |
"Please turn off object classification first" |
Disable object classification. |
2007 |
"Please turn off ITS first" |
Disable ITS. |
2008 |
"Please turn off queue detection first" |
Disable queue detection. |
2009 |
"Please turn off crowd density detection first" |
Disable crowd density detection. |
2010 |
"Please turn off IBALL first" |
Disable traffic violation detection of the PTZ dome camera. |
2011 |
"Please turn off Multi-purpose algorithm first" |
Disable the full intelligence mode. |
2012 |
"This algorithm is not supported in the current mode" |
This algorithm is not supported in the current mode. |
2013 |
"VHD detection is not supported in the corridor mode, please close the corridor mode first" |
Object classification does not support the corridor mode. Disable the corridor mode. |
2014 |
"Please turn off enhanced mode behavior analysis first" |
Disable the intelligent alarming function. |
2015 |
"Please turn off import and export business first" |
Disable vehicle detection at entrances and exits. |
2016 |
"Please turn on domestic license plate algorithm first" |
Vehicle detection at entrances and exits supports only algorithms for recognizing Chinese license plates. |
2017 |
"Please turn off motion detection first" |
Disable the motion detection function. |
2018 |
"Please turn off the blocking detection function first" |
Disable the lens blocking detection function. |
2019 |
"Please turn off the scene change function first" |
Disable the scene change detection function. |
2020 |
"Please turn off the virtual focus detection function first" |
Disable the defocus detection function. |
2021 |
"Please turn off the people gathering function first" |
Disable the crowd gathering detection function. |
2022 |
"Please turn off the heat map function first" |
Disable the heat map function. |
2023 |
"Please turn off all vehicle event services first" |
Disable all vehicle event detection functions. |
2024 |
"Please turn off the traffic flow statistics business first" |
Disable the traffic flow statistics function. |
2025 |
"Please turn off video quality diagnosis first" |
Disable video quality diagnosis. |
2026 |
"Please turn off the electronic anti-shake service first" |
Disable electronic image stabilization. |
2027 |
"Please turn off all other businesses first" |
Disable all other algorithms. |
2029 |
"Please turn off target recognition first" |
Disable target recognition. |
2030 |
"Please turn off target snapshot high-density mode first" |
Disable the high-density target capture mode. |
2031 |
"Please turn off traffic flow campus first" |
Disable the video-based vehicle detector. |
2032 |
"Please turn off fighting first" |
Disable fight detection. |
2033 |
"Please turn off climbing first" |
Disable climbing detection. |
2034 |
"Please turn off fall down first" |
Disable fall detection. |
2035 |
"Please turn off target running first" |
Disable running detection. |
2036 |
"Please turn off target timed snapshot first" |
Disable the scheduled snapshot mode for target recognition. |
2037 |
"Please turn off fire detect first" |
Disable fire detection. |
2038 |
"Please turn off temperature control first" |
Disable the temperature measurement function. |
2039 |
"Please turn off visible behavior first" |
Disable the visible light channel. |
2040 |
"Please turn off thermal behavior first" |
Disable the thermal imaging channel. |
2043 |
"Please turn off target attribute first" |
Disable target attribute recognition. |
2044 |
"Please turn off continuous image quality evaluation" |
Disable continuous image quality diagnosis. |
2045 |
"Please turn off target low bandwidth snapshot first" |
Disable the low-bandwidth snapshot mode for target detection. |
2046 |
"Please turn off mixed line first" |
Disable the full intelligence mode. |
2047 |
"Please turn off radar linkage first" |
Disable the radar-PTZ dome camera linkage function. |
2048 |
"Please turn off 1 + N mode first." |
Disable 1 + N. |
2049 |
"Please turn off radar Intrusion first" |
Disable radar- and PTZ dome camera-based intrusion detection. |
2050 |
"Please turn on target attribute first" |
Enable the target attribute recognition function. |
2051 |
Please turn off the mask alarm first" |
Disable the mask alarm function. |
2052 |
"Please turn off human attributes first" |
Disable personal attribute recognition. |
2053 |
"Please turn off leave detection first" |
Disable absence detection. |
2054 |
"Please turn off hot region analysis first" |
Disable hot zone analysis. |
2055 |
"Vehicle detection is not supported in corridor mode, please turn off corridor mode first." |
Motor vehicle detection and the corridor mode cannot be enabled at the same time. To enable motor vehicle detection, disable the corridor mode first. |
2056 |
"Please turn off detection of electronic mobile invasion in elevator first" |
Disable the function of detecting electric bikes in elevators first. |
2057 |
"Multiple functions have been enabled, turn off these functions first" |
Multiple mutually exclusive functions are enabled. Use the corresponding interface to obtain the list of mutually exclusive functions. Disable all mutually exclusive functions. |
2058 |
"Scheduled capture and duplicate object filtering cannot be enabled at the same time" |
Scheduled capture and target deduplication in advanced parameters cannot be enabled at the same time. |
2059 |
"Disable access control mode first" |
Disable the access control capture mode first. |
2060 |
"Live osd and pic synthesis cannot be enabled at the same time" |
OSD overlay on live video and image combination cannot be enabled at the same time. |
2061 |
"Please turn off omni-data structuring first." |
Disable the omni-data structuring function first. |
2063 |
"Please turn off PPPOE" |
Disable the PPPoE function first. |
2064 |
"Please turn off CloudService protocol" |
Disable the cloud service connection protocol first. |
2065 |
"The intelligent service is not enabled." |
The intelligent service is not enabled. |
2066 |
"Primary-secondary camera linkage and image combination cannot be both enabled" |
Primary-secondary camera linkage and image combination cannot be both enabled. |
2068 |
"Please turn off intelligent video tag first" |
Disable intelligent recording analysis first. |
2069 |
"Fast snapshot mode and duplicate object filtering are mutually exclusive" |
Fast snapshot and duplicate target filtering cannot be both enabled. |
2070 |
"Please turn off the intelligent cruise first" |
Disable intelligent inspection first. |
2071 |
"Please configure the limit angle first" |
Configure the limiting angle first. |
2072 |
"Please configure the limit area first" |
Configure a limiting area first. |
2073 |
"The review picture does not exist" |
The recheck image does not exist. |
2074 |
"Close business timeout" |
Service disabling timed out. |
2075 |
"The process does not exist." |
The process does not exist. |
2100 |
"Target lib load success" |
Target imported to the target library successfully. |
2101 |
"Target recognition enable fail" |
Target recognition is not enabled. |
2102 |
"Target Data update fail" |
Failed to update the data. |
2103 |
"Unsupport target operation" |
The operation is not supported. |
2104 |
"Target lib load fail" |
The batch import operation is not complete. |
2105 |
"Target lib oversize" |
The number of target libraries exceeds the upper limit. |
2106 |
"Target num oversize" |
The number of targets exceeds the upper limit. |
2107 |
"Target db operate fail" |
The database operation fails. |
2108 |
"Target lib repeat" |
Duplicate target list. |
2109 |
"Target pic oversize" |
The image width or height is out of range. |
2110 |
"Target pic decode fail" |
Image decoding failure. |
2111 |
"Target detection fail" |
Failed to detect targets. |
2112 |
"Target feature extract fail" |
Failed to extract target features. |
2113 |
"Target dao fail" |
Failed to write target data into the database. |
2114 |
"Target file write fail" |
Failed to write target data into the file. |
2115 |
"Target algorithm disable" |
The target algorithm is disabled. |
2116 |
"No target lib feature" |
There is no feature in the target library. |
2117 |
"Target zip fail" |
Failed to decompress the ZIP package. |
2118 |
"Target Csv fail" |
Failed to parse the CSV file. |
2119 |
"Target encrypt or decrypt fail" |
Failed to encrypt or decrypt target data. |
2120 |
"Target Task proc fail" |
The task is not processed. |
2121 |
"Target feature extract success" |
Features extracted successfully. |
2122 |
"Target feature extracted" |
Features extracted. |
2123 |
"Target recognition enable fail" |
The target recognition function fails to be enabled because the algorithm package does not exist or the version does not match. |
2124 |
"Target feature loading" |
Target recognition is being loaded (including historical alert deployment and image names). |
2125 |
"Target feature importing" |
The feature package is being imported. |
2126 |
"Target Pic importing" |
The image package is being imported. |
2127 |
"Target feature exporting" |
Features are being exported. |
2128 |
"Target feature extracting" |
Features are being extracted. |
2129 |
"Target pic quality clearness error" |
The target image is not clear enough. |
2130 |
"Target pic quality kps error" |
The target is severely blocked. |
2131 |
"Does not support high-density target capture" |
High-density target capture is not supported. |
2132 |
"Device EMMC status abnormal" |
The eMMC card status is abnormal. |
2133 |
"Target quick snapshot not support black" |
Ultra-fast snapshot can be based on alerts excluding blocklist-based alert. |
2134 |
"Device disk space not enough" |
Insufficient disk space. |
2135 |
"Target record check error" |
Failed to verify the target record. |
2136 |
"Target recognition multiframe not support" |
Multi-frame integration for target recognition is not supported. |
2137 |
"Please turn off target recognition multiframe fusion first" |
Disable multi-frame integration for target recognition. |
2138 |
"read feature structure from feature file fail" |
Failed to read the feature structure from the feature.bin file. |
2139 |
"read feature notifyone fail" |
Failed to encapsulate data in the NotifyOne. |
2140 |
"Database encrypt key error" |
Incorrect database key. |
2141 |
"json file parse fail" |
Failed to parse the JSON file. |
2142 |
"target picture extract processing" |
A single image extraction task is in progress (NVR800). |
2143 |
"Target picture extract timeout" |
The single image extraction task timed out. |
2144 |
"Target library control oversize" |
The number of alert target libraries exceeds the upper limit. |
2145 |
"Target picture not existence" |
Image does not exist. |
2146 |
"The file exceeds the allowed size" |
The file size exceeds the threshold. |
2147 |
"Please turn off feature synergy first" |
Disable the feature-based collaboration function. |
2148 |
"Please start preferred capture first" |
Enable the prioritized snapshot function. |
2149 |
"Duplicate picture name" |
The image name exists. |
2150 |
"The number of target records in the zip package is out of range" |
The number of target records in a single .zip package exceeds the upper limit. |
2151 |
"Check files in zip fail" |
Failed to verify files in the ZIP package. |
2152 |
"Updating the secret key of the target library… Try again later." |
The key is being updated for the target list. Try again later. |
2153 |
"Target recognition not authorized!" |
Target recognition is not authorized. |
2200 |
"Setting failed. The parking detection conflicts with the mirror mode and corridor mode. Check whether any function in conflict is enabled" |
The parking detection and the corridor mode or mirror mode cannot be enabled at the same time. |
2201 |
"The corridor mode must be turned off when the Motor vehicle/Non-motor vehicle/Pedestrian mode open" |
The object classification and the corridor mode cannot be enabled at the same time. |
2202 |
"The corridor mode must be turned off when the vehicle identification open" |
The vehicle recognition and the corridor mode cannot be enabled at the same time. |
2203 |
"For -H Model,The corridor mode must be turned off in the Motor vehicle/Non-motor vehicle/Pedestrian mode (mixed line, micro card, behavior analysis is not supported)" |
(The corridor mode must be disabled for -H camera models in non-target checkpoint mode (not supported in full intelligence, micro checkpoint, and behavior analysis modes).) |
2300 |
"Failed to obtain the license content because the license is invalid" |
Failed to obtain the license content due to the invalid license. |
2301 |
"Duplicate ESN or incorrect license file version" |
The ESN cannot be loaded repeatedly or the license file that does not match the device version cannot be loaded. |
2302 |
"License file is invalid" |
Invalid license file. |
2303 |
"The license file does not contain the product feature segment" |
The license file does not contain the product feature segment. |
2304 |
"Product name is invalid" |
Invalid product name. |
2305 |
"The license file has expired" |
The license file has expired. |
2306 |
"Failed to obtain the control item configuration value" |
Failed to obtain the control item configuration. |
2307 |
"The license file has expired" |
The license file has expired. |
2308 |
"You are not allowed to load a commissioning license file whose ESN is ANY and validity period is six months repeatedly" |
You are not allowed to repeatedly load a commissioning license file whose ESN is ANY and validity period is six months. |
2309 |
"The number of features in the license file exceeds the maximum" |
The number of features in the license file exceeds the maximum. |
2310 |
"The feature type in the license file is incorrect" |
The feature type in the license file is incorrect. |
2311 |
"The license component is not started" |
The license component is not started. |
2312 |
"All features in the license file expired or are in the trial period" |
All features in the license file expired or in the trial period. |
2313 |
"The ESN in the license file is different from the actual ESN" |
The ESN in the license file is different from the actual ESN. |
2314 |
"The license file version is inconsistent with the actual version" |
The device version in the license file is different from the actual version. |
2315 |
"No activated license is available" |
No activated license is available. |
2316 |
"The target identification license is missing" |
The target recognition license is missing. |
2317 |
"Failed to verify the license validity period" |
Failed to verify the license validity period. |
2318 |
"The license cannot be revoked in the current state" |
The license cannot be invalidated in the current state. |
2450 |
"Error in enabling or disabling SMTP." |
An error occurred when enabling or disabling SMTP. |
2451 |
"Incorrect mail type." |
Incorrect email type. |
2452 |
"Incorrect mail encryption type." |
Incorrect email encryption type. |
2453 |
"Error in enabling or disabling the function of sending image attachments." |
An error occurred when enabling or disabling the image attachment. |
2454 |
"Incorrect number of images." |
Incorrect image quantity. |
2455 |
"Incorrect image capture interval." |
Incorrect snapshot interval. |
2456 |
"Incorrect server port number." |
Incorrect server port. |
2457 |
"Error in enabling or disabling server authentication." |
Incorrect server authentication settings. |
2458 |
"Incorrect server name." |
Incorrect server name. |
2459 |
"Incorrect server password." |
Incorrect server password. |
2460 |
"Incorrect server IP address." |
Incorrect server IP address. |
2461 |
"Incorrect sender name." |
Incorrect sender name. |
2462 |
"Incorrect sender address." |
Incorrect sender address. |
2463 |
"Incorrect recipient information." |
Incorrect receiver information. |
2464 |
"Incorrect server name or password." |
Incorrect server name or password. |
2520 |
"MTU error in the IPv6 scenario" |
The MTU is incorrect in the IPv6 scenario. |
2521 |
"The gateway configuration of the dual network adapters conflicts" |
Gateway address configuration conflict for dual network adapters. |
2522 |
"The following network segment IP addresses are not allowed: 127.0. 0.1/8, 169.254. 0.0/16" |
IP addresses in the 127.0.0.1/8 and 169.254.0.0/16 network segments cannot be used. |
2523 |
"IPv6 address conflict" |
IPv6 address conflict. |
2524 |
"Only IP addresses in the same network segment can be added." |
Only IP addresses in the same network segment can be added. |
2525 |
"The IP address is in the same network segment as that of the other network adapter's IP address." |
The IP address is in the same network segment as that of the other network adapter's IP address. |
2527 |
"For a camera with dual network adapters, IPv6 addresses cannot be dynamically allocated to both of the network adapters." |
For a camera with dual network adapters, IPv6 addresses cannot be dynamically allocated to both of the network adapters. |
2528 |
"IP address conflicts with the gateway address" |
The IP address conflicts with the gateway address. |
2600 |
"Intelligent analysis license is invalid" |
Invalid intelligent analysis license. |
2720 |
"GB35114 illegal parameters" |
Invalid GB 35114 certificate parameter. |
2721 |
"GB35114 not support" |
The GB 35114 encryption function is not supported. |
2722 |
"GB35114 cache not enough" |
Insufficient GB 35114 cache. |
2723 |
"GB35114 no permission" |
Insufficient permission on the GB 35114 TF card. |
2724 |
"GB35114 error format" |
The format of the GB 35114 certificate is incorrect. |
2725 |
"GB35114 error PIN code" |
The PIN of the GB 35114 TF card is incorrect. |
2726 |
"GB35114 key not exist" |
The GB 35114 certificate key does not exist. |
2727 |
"GB35114 certificate not exist" |
The GB 35114 certificate does not exist. |
2728 |
"GB35114 illegal certificate" |
Invalid GB 35114 certificate format. |
2729 |
"GB35114 certificate out of date" |
The validity period of the GB 35114 certificate is invalid. |
2730 |
"GB35114 fail to decrypt VKEY" |
Failed to decrypt the VKEY using GB 35114. |
2731 |
"GB35114 fail to encrypt VEK" |
Failed to encrypt the VEK using GB 35114. |
2732 |
"GB35114 fail to decrypt VEK" |
Failed to decrypt the VEK using GB 35114. |
2733 |
"GB35114 fail to calculate HASH" |
GB 35114 hash algorithm failed. |
2734 |
"GB35114 fail to sign" |
GB 35114 signature failed. |
2735 |
"GB35114 fail to check signature" |
GB 35114 signature verification failed. |
2736 |
"GB35114 fail to decode base64 string" |
GB 35114 Base64 decoding failed. |
2737 |
"GB35114 fail to decode DER file" |
GB 35114 DER decoding failed. |
2738 |
"GB35114 device not found" |
No GB 35114 device is found. |
2739 |
"GB35114 fail to open device" |
Failed to open the GB 35114 device. |
2740 |
"GB35114 fail to deal with device" |
Failed to process the GB 35114 device. |
2741 |
"GB35114 device is locked" |
The GB 35114 PIN has been locked. |
2742 |
"GB35114 error file size" |
Incorrect GB 35114 file size. |
2743 |
"GB35114 file not exist" |
The GB 35114 file does not exist. |
2744 |
"GB35114 error file offset" |
The offset of the GB 35114 file operation is incorrect. |
2745 |
"GB35114 UKEY certification not exist" |
The GB 35114 UKEY certificate does not exist. |
2746 |
"GB35114 UKEY certification is empty" |
The GB 35114 UKEY certificate is empty. |
2747 |
"Device is online with 28181, cannot switch GB35114 mode" |
The GB/T 28181 protocol is online. The GB 35114 software and hardware modes cannot be switched. |
2748 |
"GB35114 not enable, cannot login with ukey" |
The GB 35114 is not enabled. You cannot log in using the UKey. |
2780 |
"An intelligent analysis channel needs to be created for media streams, but the intelligent analysis module is not enabled" |
An intelligent analysis channel needs to be created for media streams, but the intelligent analysis module is not enabled. |
2781 |
"Failed to enable the absolute timestamp. Disable the hierarchical encoding first" |
Failed to enable the absolute timestamp. Disable layered encoding first. |
2782 |
"Failed to enable the current service switch. Disable the absolute timestamp first" |
Failed to enable the current service. Disable the absolute timestamp first. |
2783 |
"Failed to enable the absolute timestamp. Please disable the digital watermark first" |
Failed to enable the absolute timestamp. Disable the digital watermark first. |
2800 |
"The switched mode does not support the corridor mode" |
The switched mode does not support the corridor mode. |
2801 |
"Failed to enable the algorithm for the switched mode. Check the model" |
Failed to enable the algorithm for the switched mode. Check the model. |
2802 |
"The mode is switched successfully. The FTP needs to be reconfigured" |
The mode is switched successfully. FTP needs to be reconfigured. |
2803 |
"The mode is switched successfully. Please wait for device reboot!" |
Switchover succeeded. Please wait for restart. |
2804 |
"The mode is switched successfully. Please wait!" |
Switchover succeeded. Please wait for the service to start. |
2820 |
"Intelligent alarm does not support corridor mode, please turn off corridor mode first" |
Intelligent alarms do not support the corridor mode. Disable the corridor mode. |
2821 |
"Intelligent alarm does not support corridor mode, corridor mode cannot be opened" |
The intelligent alarm does not support the corridor mode. The corridor mode cannot be enabled. |
2822 |
"Basic behavior analysis status, unable to set enhanced behavior analysis parameters" |
Basic behavior analysis status. The enhanced behavior analysis parameters cannot be set. |
2823 |
"Enhanced behavior analysis status, unable to set basic behavior analysis parameters" |
Enhanced behavior analysis status. The basic behavior analysis parameters cannot be set. |
2850 |
"Tracking initial position cannot be set during tracking" |
The initial tracking position cannot be set during the tracking. |
3000 |
"subscriber Num Reach Max" |
The number of metadata updates or alarms that SDCAPI subscribes to exceeded the maximum. |
3001 |
"Ssh username or passwd wrong" |
Incorrect SSH user name or password. |
3002 |
"Ssh sys error" |
SSH system error. |
3003 |
"Support Secure Protocol only" |
Only secure protocols are supported. |
3114 |
"rtsp para error" |
RTSP parameter error. |
3250 |
"The rotatable device is not initialized" |
The rotatable device is not initialized. |
3251 |
"An exception occurred on the rotatable device" |
An exception occurred on the rotatable device. |
3252 |
"Obtain the rotatable device log fail" |
Failed to obtain the rotatable device log. |
3253 |
"Obtain the rotatable device configuration file fail" |
Failed to obtain the rotatable device configuration file. |
3254 |
"Set the rotatable device configuration file fail" |
Failed to set the rotatable device configuration file. |
3255 |
"Restart the rotatable device fail" |
Failed to restart the rotatable device. |
3256 |
"Restore the rotatable device to default settings fail" |
Failed to restore the rotatable device to default settings. |
3257 |
"SDK internal error" |
SDK internal error. |
3258 |
"The tracking function is enabled. Therefore, calibration cannot be performed, and positioning cannot be linked. Disable the tracking function first" |
The tracking function is enabled. Therefore, calibration cannot be performed, and positioning cannot be linked. Disable the tracking function. |
3259 |
"The calibration is in progress" |
The calibration is in progress. |
3260 |
"The calibration is not complete. Therefore, positioning cannot be linked, and the tracking function cannot be enabled. Complete the calibration first" |
The calibration is not complete. Therefore, positioning cannot be linked, and the tracking function cannot be enabled. Complete the calibration. |
3261 |
"No calibration is required, no need to cancel, prompt: no calibration is in progress, no need to cancel calibration" |
No calibration is in progress. You do not need to cancel calibration. |
3262 |
"Please turn off 1 + N mode first." |
Disable 1 + N. |
3263 |
"Switching linkage Fixed point needs to be forced to switch to mixed line" |
The fixed lens needs to be forcibly switched to the full intelligence mode. |
3264 |
"Prompt user to close linkage when switching modes" |
Disable the linkage function before switching the mode. |
3265 |
"The calibration is in progress, and the 3D positioning cannot be linked." |
3D positioning cannot be associated because automatic calibration is in progress. |
3266 |
"Tracking cannot be set during calibration" |
Tracking cannot be set because automatic calibration is in progress. |
3267 |
"Linkage setting is successful, target recognition setting fails" |
Linkage is successful but target recognition setting fails. |
3268 |
"The linkage setting is successful, the target recognition setting fails, the fixed point has been switched to the mixed line mode, the browser is about to refresh" |
Linkage is successful but target recognition setting fails. The fixed lens has switched to full intelligence mode and the web page will be refreshed. |
3269 |
"Turn on linkage tracking, unable to set target preference mode" |
Linked tracking is enabled for the rotatable lens, so the target capture mode cannot be set to optimal. |
3270 |
"Unable to calibrate in mirror mode" |
The calibration cannot be performed in mirroring mode. |
3271 |
"Rotatable device 1 failed to set tracking parameters" |
Failed to set tracking parameters for rotatable lens 1 of the dual-PTZ compound-eye camera. |
3272 |
"Rotatable device 2 failed to set tracking parameters" |
Failed to set tracking parameters for rotatable lens 2 of the dual-PTZ compound-eye camera. |
3273 |
"Rotatable device failed to set tracking parameters" |
Failed to set tracking parameters for the rotatable lens of the single-PTZ compound-eye camera. |
3274 |
"Failed to set tracking parameters at fixed point" |
Failed to set tracking parameters for the fixed lens of the omni-data structuring camera. |
3275 |
"Failed to obtain the configuration file of the rotatable device 2001" |
Failed to obtain the configuration file of rotatable lens 2001. This code is returned when the configuration file of one of the two rotatable lenses fails to be obtained. |
3276 |
"Failed to obtain the configuration file of the rotatable device 2002" |
Failed to obtain the configuration file of rotatable lens 2002. This code is returned when the configuration file of one of the two rotatable lenses fails to be obtained. |
3277 |
"Failed to set rotatable device 2001 configuration file" |
Failed to set the configuration file of rotatable lens 2001. This code is returned when the configuration file of one of the two rotatable lenses fails to be set. |
3278 |
"Failed to set rotatable device 2002 configuration file" |
Failed to set the configuration file of rotatable lens 2002. This code is returned when the configuration file of one of the two rotatable lenses fails to be set. |
3279 |
"rotatable device 2001 restart failed" |
Failed to restart rotatable lens 2001. This code is returned when one of the two rotatable lenses fails to be restarted. |
3280 |
"rotatable device 2002 restart failed" |
Failed to restart rotatable lens 2002. This code is returned when one of the two rotatable lenses fails to be restarted. |
3281 |
"Failed to get system time of all rotatable device" |
Failed to obtain the time of all rotatable lenses. |
3282 |
"Failed to get system time of rotatable device 2001" |
Failed to obtain the time of rotatable lens 2001. This code is returned when the time of one of the two rotatable lenses fails to be obtained. |
3283 |
"Failed to get system time of rotatable device 2002" |
Failed to obtain the time of rotatable lens 2002. This code is returned when the time of one of the two rotatable lenses fails to be obtained. |
3284 |
"Failed to set system time of all rotatable device" |
Failed to set the time of all rotatable lenses. |
3285 |
"Failed to set system time of rotatable device 2001" |
Failed to set the time of rotatable lens 2001. This code is returned when the time of one of the two rotatable lenses fails to be set. |
3286 |
"Failed to set system time of rotatable device 2002" |
Failed to set the time of rotatable lens 2002. This code is returned when the time of one of the two rotatable lenses fails to be set. |
3287 |
"Failed to get all rotatable device for summer time" |
Failed to obtain the DST of all rotatable lenses. |
3288 |
"Failed to get rotatable device 2001 for summer time" |
Failed to obtain the DST of rotatable lens 2001. This code is returned when the DST of one of the two rotatable lenses fails to be obtained. |
3289 |
"Failed to get rotatable device 2002 for summer time" |
Failed to obtain the DST of rotatable lens 2002. This code is returned when the DST of one of the two rotatable lenses fails to be obtained. |
3290 |
"Failed to set all rotatable device for summer time" |
Failed to set the DST of all rotatable lenses. |
3291 |
"Failed to set rotatable device 2001 for summer time" |
Failed to set the DST of rotatable lens 2001. This code is returned when the DST of one of the two rotatable lenses fails to be set. |
3292 |
"Failed to set rotatable device 2002 for summer time" |
Failed to set the DST of rotatable lens 2002. This code is returned when the DST of one of the two rotatable lenses fails to be set. |
3293 |
"Fixed device setting failed" |
Failed to configure the fixed lens of the omni-data structuring camera for target recognition. |
3294 |
"Setting of rotatable device 1 failed" |
Failed to configure rotatable lens 1. |
3295 |
"Setting of rotatable device 2 failed" |
Failed to configure rotatable lens 2. |
3300 |
"To enable the online self-learning algorithm, you need to enable target detection and target and body attributes" |
Enable target detection and target and personal attribute recognition before enabling the online learning algorithm. |
3301 |
"Please start the online self-learning algorithm first" |
Enable the online learning algorithm. |
3302 |
"The online self-learning algorithm is being trained and cannot be retrained" |
The online learning algorithm is being trained and cannot be trained again. |
3303 |
"The online self-learning algorithm is being trained, and the target and body attributes cannot be turned off" |
The online learning algorithm is being trained. Target and personal attribute recognition cannot be disabled. |
3503 |
"1TN disabled" |
The 1+N function is disabled. |
3504 |
"Display item of target recognition information exceeds specification" |
The number of displayed target recognition items in 1 + N mode exceeds the upper limit. |
3505 |
"Delete Time Period is bigger than one day" |
The content has been deleted for more than one day. |
3506 |
"Delete start time later than end time" |
The deletion start time is later than the end time. |
3507 |
"Delete end time later than current time" |
The deletion start time is later than the current time. |
3554 |
"Length of question is invalid." |
Invalid question length. |
3555 |
"Format of answer is invalid." |
Invalid answer format. |
3556 |
"Function of password reset is locked." |
The password resetting function is locked. |
3557 |
"Answer Verification failed" |
Failed to verify the security question. |
3601 |
"A maximum of three protocols can be enabled at the same time: 28181, 1400, ONVIF, Cloud, and hw SDK" |
A maximum of three of the following protocols can be enabled at the same time: GB/T 28181, GA/T 1400, ONVIF, cloud service protocol, and SDK. |
3800 |
"Need to manually capture and evaluate" |
Perform manual snapshot for evaluation. |
3900 |
"Failed to save configuration" |
Failed to save the configuration. |
4001 |
"The app not found." |
App not found. |
4002 |
"The app is busy. Please try again later." |
The app is busy. Try again later. |
4003 |
"Invalid app operation." |
Invalid app operation. |
4202 |
"Failed to configure the app environment." |
Failed to configure the app environment. |
4211 |
"Not enough space for App (flash and sdcard)" |
Insufficient space (including the flash memory and SD card space) for installing the app. |
4212 |
"The app file path does not exist." |
The app file path does not exist. |
4219 |
"Failed to delete the app file." |
Failed to delete the app file. |
4232 |
"The installation package is inconsistent with the SDC architecture". |
The installation package is inconsistent with the SDC architecture. |
4247 |
"Not enough space for App (sdcard)" |
Insufficient SD card space for installing the app. |
4248 |
"Not enough space for App (flash)" |
Insufficient flash memory for installing the app. |
4255 |
"Failed to mount disk" |
Disk mounting failed. |
4500 |
"security code is invalid" |
The anti-counterfeit code does not exist. |
4501 |
"security code file size is greater than 10M" |
The size of the anti-counterfeit code file is greater than 10 MB. |
4502 |
"security code verify success" |
The anti-counterfeit code is successfully verified. |
4503 |
"security code verify failed" |
The anti-counterfeit code fails to be verified. |
4700 |
"The num of template exceed max num" |
The number of templates exceeds the threshold. |
4701 |
"The num of osd exceed max num" |
The number of OSD items exceeds the threshold. |
4702 |
"The len of content exceed max len" |
The length of OSD content exceeds the threshold. |
4703 |
"The name repeating" |
The OSD template name already exists. |
4704 |
"The content contains invalid character" |
Invalid characters exist. |
4705 |
"The coordinate value is invalid" |
The coordinate value is invalid. |
4706 |
"osd or pic overlay enable error" |
Both OSD overlay and image overlay are enabled. |
4707 |
"osd enable error" |
The OSD enabling status is invalid. |
4708 |
"osd id value error" |
The OSD ID is invalid. |
4709 |
"osd invert enable error" |
The OSD color invert setting is invalid. |
4710 |
"osd font size error" |
The OSD font size is invalid. |
4711 |
"osd background color value error" |
The font background color is invalid. |
4712 |
"osd background transparent value error" |
The font background transparency is invalid. |
4713 |
"osd line space value error" |
The font line spacing is invalid. |
4714 |
"template name len error" |
The length of the template name is invalid. |
4715 |
template enable value error" |
The template enabling status is valid. |
4716 |
"template id value error" |
The template ID is invalid. |
4717 |
"osd font transparent value error" |
The font transparency is invalid. |
4718 |
"template refsize value error" |
The reference size is invalid. |
4719 |
"osd color value error" |
The color is invalid. |
4720 |
"osd param value error" |
The OSD parameter is invalid. |
4721 |
"last osd template cannot be deleted" |
The last OSD template cannot be deleted. |
4722 |
"osd alignment error" |
Incorrect OSD alignment mode. |
4723 |
"The number of OSD wraps outside the image exceeds the upper limit." |
The number of OSD line feeds out of the image exceeds the upper limit. |
4724 |
"The number of OSD line breaks in the image exceeds the upper limit." |
The number of OSD line feeds in the image exceeds the upper limit. |
4725 |
"The number of spaces in the image OSD exceeds the upper limit." |
The number of spaces in image OSDs exceeds the upper limit. |
5000 |
"Please first configure the details as human card mode and panorama as mixed mode" |
Select the target checkpoint mode for the zoom lens and full intelligence mode for the wide-angle prime lens. |
5001 |
"Please first configure the capture mode of details and panorama as the preferred mode" |
Set the snapshot mode to the preferred mode for the zoom and wide-angle prime lenses. |
5002 |
"Please enable calibration first" |
Enable calibration. |
5003 |
"Please close binocular association first" |
Disable dual-lens association. |
5199 |
"Incorrect ftp directory" |
Incorrect FTP directory settings. |
5201 |
"ftp test ip address error" |
Invalid test FTP IP address. |
5202 |
"ftp test upload file error" |
Failed to upload images during the FTP test. |
5203 |
"ftp param error" |
The FTP parameter specifications are incorrect. |
5204 |
"ftp Login admin/pwd error" |
The FTP user name or password is incorrect. |
5205 |
"ftp check success" |
The FTP test succeeds. |
5211 |
"sftp test ip address error" |
The SFTP IP address is invalid. |
5212 |
"sftp test upload file error" |
Failed to upload images during the SFTP test. |
5213 |
"sftp param error" |
The SFTP parameter specifications are incorrect. |
5214 |
"sftp Login admin/pwd error" |
The SFTP user name or password is incorrect. |
5215 |
"sftp check success" |
The SFTP test succeeds. |
5401 |
"The wakeup switch parameter is invalid" |
Invalid parameter for enabling or disabling wake-up. |
5402 |
"Invalid wakeup mode" |
Invalid wake-up mode. |
5404 |
"Invalid timed wake-up hold time" |
Invalid scheduled wake-up duration. |
5405 |
"Incorrect time point wakeup parameter" |
Incorrect time-based wake-up parameters. |
5406 |
"Incorrect number of wakeup time points" |
The number of wake-up time points is incorrect. |
5407 |
"Invalid wakeup interval" |
Invalid scheduled wake-up interval. |
5408 |
"Enable at least one wakeup mode" |
Enable at least one wake-up policy. |
5410 |
"Overlapping time zones" |
The time ranges overlap. |
5411 |
"Invalid cruise direction point" |
Invalid tour point. |
5412 |
"More than 24 hours" |
The time span exceeds 24 hours. |
5414 |
"The device is upgrading. The device cannot enter sleep mode, in current mode." |
The device is being upgraded. The device cannot enter sleep mode after it is waken up from deep sleep. |
5500 |
"IP ping fail" |
The IP address cannot be pinged. |
5502 |
"IP ping too frequently fail" |
The IP address ping operation is performed too frequently. |
5700 |
"duplicate audio file name" |
The audio file name exists. |
5701 |
"too many audio files" |
The number of audio files exceeds the upper limit. |
5702 |
"audio file action not support" |
The audio file operation is not supported. |
5703 |
"audio file not found" |
No audio file found. |
5704 |
"too large audio file" |
The audio file is too large. |
5705 |
"Play Count Exceeded" |
The number of playback times exceeds the limit. |
5706 |
"The file name contains a maximum of 20 characters" |
The length of the audio file name exceeds the upper limit. |
5707 |
"The audio file size exceeds {0} KB." |
The audio file size exceeds 75 KB. |
5800 |
"Invalid audio encoding format." |
Invalid audio encoding format. |
5801 |
"Invalid bit rate." |
Invalid bit rate. |
5802 |
"Invalid audio channel." |
Invalid audio channel. |
5803 |
"Invalid sampling rate." |
Invalid sampling rate. |
5804 |
"Invalid audio input or output gain. The gain value must range from 0 to 100." |
The audio input and output gains are invalid. The value ranges from 0 to 100. |
5805 |
"Invalid audio input type." |
Invalid audio input type. The value must be mic in or line in. |
5806 |
"Invalid value for enabling or disabling automatic audio gain." |
Auto audio gain must be set to true or false. |
5807 |
"Invalid value for enabling or disabling echo cancellation." |
Echo cancellation must be set to true or false. |
5808 |
"Invalid value for enabling or disabling environment noise filtering." |
Environment noise filtering must be set to true or false. |
5809 |
"Audio alarm is supported." |
Audible alarms are supported. |
5810 |
"Audio alarm is not supported." |
Audible alarms are not supported. |
5811 |
"Invalid audio channel ID" |
Invalid audio channel ID. |
5812 |
"Invalid UUID." |
Invalid UUID. |
5814 |
"Failed to set audio parameters." |
Failed to set audio data. |
7000 |
"The cloud service conflicts with the 28181 service and cannot be used at the same time." |
The cloud service and the GB/T 28181 protocol cannot be enabled at the same time. |
7100 |
"The pre-upgrade command times out" |
Sending the pre-upgrade command timed out. |
7101 |
"Failed to request the URI for software package" |
Failed to request the URI for downloading the upgrade package. |
7102 |
"Failed to download the software package" |
Failed to download the software package. |
7103 |
"Power interruption during the upgrade" |
The system was powered off and restarted during upgrade. |
7104 |
"Invalid file name of software package" |
Invalid file name of the software upgrade package. |
7105 |
"The device is being upgraded." |
Updating… |
7106 |
"Failed to check the version" |
Failed to check the device version (by comparing the device version specified in version.bin of the cloud service). |
7107 |
"The device is busy, please try again later" |
The device is busy. Please try again later. |
7120 |
"The device is not online to the cloud service" |
The device is not online on the cloud service. |
7500 |
"Corridor mode conflicted with current intelligent mode" |
The corridor mode is mutually exclusive with the current intelligent analysis function. |
7501 |
"SuperCoding and region crop cannot be enabled at the same time." |
SuperCoding and area cropping are mutually exclusive. |
7502 |
"Corridor mode conflicted with TGateWay mode." |
The corridor mode is mutually exclusive with the intelligent checkpoint mode. |
8000 |
"SD card is full." |
The SD card is full. |
8001 |
"Collaborative Snap is enable" |
The common snapshot parameters cannot be set when collaborative snapshot is enabled. |
8100 |
"The length of the weak password should be between 6 and 32" |
The weak password needs to have 6 to 32 characters. |
8101 |
"The specified secondary stream resolution is not supported in the current primary stream resolution." |
The specified resolution of the secondary stream is not supported in the current primary stream. |
8102 |
"Stream is not enabled." |
The current stream is not enabled. |
8103 |
"802.1x certificate not exist." |
The 802.1X certificate does not exist. |
12001 |
"The ID of the behavior analysis template is duplicate." |
Duplicate behavior analysis template ID. |
12002 |
"Failed to extract feature values." |
Failed to extract features. |
12003 |
"Missing deviceID or SHA256" |
No device ID or SHA256. |
12004 |
"Please disable edge collaboration first" |
Disable device-edge synergy first. |
12005 |
"Please confirm if you want to force import." |
Confirm whether to perform forcible import. |
0xF7104016 |
"Process does not exist." |
The process does not exist. |
0xF7180005 |
"The file size exceeds the limit." |
The file size exceeds the limit. |